Use the form below to find the searched projects. Enter your criteria for searching (single or in combination) in the fields below and press the button “Search”.
Amendment 1 - Compression and mechanical connectors for power cables - Part 1-3: Test methods and requirements for compression and mechanical connectors for power cables for rated voltages above 1 kV (U<sub>m</sub> = 1,2 kV) up to 30 kV (U<sub>m</sub> = 36 kV) tested on non-insulated conductors
20.99 WD approved for registration as CD
Nuclear instrumentation - Portable gamma radiation meters and spectrometers used for prospecting - Definitions, requirements and calibration
40.20 DIS ballot initiated: 12 weeks
Determination of long-term radiation ageing in polymers - Part 1: Techniques for monitoring diffusion-limited oxidation
30.20 CD study/ballot initiated
Materials for printed boards and other interconnecting structures - Part 2-54: Reinforced base materials clad and unclad - Halogenated modified or unmodified resin system, woven E-glass laminate sheets of defined dissipation factor (less than 0,005 at 10 GHz) and flammability (vertical burning test), copper-clad for high speed applications
40.99 Full report circulated: DIS approved for registration as FDIS
Materials for printed boards and other interconnecting structures - Part 2-55: Reinforced base materials clad and unclad - Non-halogenated modified or unmodified resin system, woven E-glass laminate sheets of defined dissipation factor (less than 0,005 at 10 GHz) and flammability (vertical burning test), copper-clad for high speed applications
30.99 CD approved for registration as DIS
Materials for printed boards and other interconnecting structures - Part 2-56: Reinforced base materials clad and unclad – Non-halogenated epoxide modified bismaleimide/triazine with filler woven glass laminate sheets of low thermal expansion and flammability (vertical burning test), copper-clad for IC substrate
30.20 CD study/ballot initiated
Materials for circuit boards and other interconnecting structures - Part 3-6: Sectional specification set for unreinforced base materials clad and unclad - Polytetrafluoroethylene (PTFE) filled laminate sheets of defined flammability (vertical burning test), copper-clad
60.00 Standard under publication
Nuclear power plants - Instrumentation and control systems important to safety - Detection of leakage in coolant systems
50.99 FDIS or proof approved for publication
Electrical insulating materials and systems - Part 2: DC voltage endurance evaluation
30.60 Close of voting/ comment period
Amendment 1 - Fibre-optic communication subsystem test procedures - Part 4-2: Installed cabling plant - Single-mode attenuation and optical return loss measurements
40.20 DIS ballot initiated: 12 weeks
Overhead lines - Requirements and tests for fittings
50.99 FDIS or proof approved for publication
Optical amplifiers - Test methods - Part 11-1: Polarization mode dispersion parameter - Jones matrix eigenanalysis (JME)
40.20 DIS ballot initiated: 12 weeks
Optical amplifiers - Test methods - Part 3-2: Noise figure parameters - Electrical spectrum analyzer method
60.00 Standard under publication
Insulating liquids - Determination of the partial discharge inception voltage (PDIV) - Test procedure
20.99 WD approved for registration as CD
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19: Tests - Damp heat (steady state)
30.99 CD approved for registration as DIS
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-21: Tests - Composite temperature/humidity cyclic test
50.20 Proof sent to secretariat or FDIS ballot initiated: 8 weeks
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-28: Tests - Corrosive atmosphere (sulphur dioxide)
20.99 WD approved for registration as CD
English